It is currently Fri Nov 15, 2019 2:33 am


Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: synscan porla position
PostPosted: Thu Feb 18, 2016 8:15 am 
Offline

Joined: Fri Oct 10, 2014 8:12 am
Posts: 121
Location: earby lancs
Hi on the synscan hand set v4 it gives you two sets of information on the porla scope I think it the p.position and ha witch one should I go off as I'm not sure as when I set the telescope up everything lines up pretty good then it seams to wonder off when changing objects any help would be great

_________________
Skywatcher 200p explorer EQ5 mount synscan upgrade kit
Nikon D3100


Top
 Profile Send private message  
 
PostPosted: Thu Feb 18, 2016 8:07 pm 
Offline

Joined: Fri Dec 03, 2004 9:58 pm
Posts: 3558
Location: Wellingborough
Hi Speedy.

I haven't used the synscan handsets so I had to do some reading up on this - hope I've got it right :)

In the user manual for the EQ5 synscan handset , under the section titled "Display Polaris Position" it gives
“Polaris Position in P.Scope = HH:MM”.
Where the HH:MM is the current position of Polaris set against an imaginary 12-hour clockface coinciding with the "large circle" in the Polarscope field of view. I assume that 12-o'clock is at the top of the field of view and the "hours" go round clockwise from 1 to 11. Each gap between the hours in the hour circle becomes 0-60 minutes (not 5 minutes as in a real clock) so it is probably quite difficult to place Polaris with better than 5 minutes accuracy.

In that case a Polaris position in the P. Scope of 12:30 would be halfway between 12 o'clock and 1 o'clock. A P. Scope position 06:45 would be three-quarters the way from 6 o'clock to 7 o'clock. These positions are what the handset refers to as "The hour-angle of Polaris", and it reads the value back to you when you confirm that you have aligned the mounting to that position (press Enter). Of course, before you press Enter, you will need to use the altitude and azimuth screws on the mounting to place Polaris at the correct position in the polarscope field of view.

From there the handset can use the star alignment steps to calculate corrections in software for any small errors in the polar alignment.

Just a couple of pointers I picked up elsewhere. Firstly make sure the mounting base is as level as possible - maybe use a small spirit level to check. Don't rely on the small circular level that may be built into the base. Secondly make sure you have a sufficiently reliable power supply to the mounting. Batteries can run down and low power can result in the goto problems you have described.

Hope I got it right and this maybe helps you a little,

Regards,

_________________
Brian
52.3N 0.6W
Wellingborough UK.

254mm LX90 on Superwedge, WO ZS66SD, Helios 102mm f5 on EQ1, Hunter 11x80, Pentax 10x50
ASI120MC Toucam Pros 740k/840k/900nc mono, Pentax K110D
Ro-Ro roof shed


Top
 Profile Send private message  
 
PostPosted: Fri Feb 19, 2016 4:23 pm 
Offline

Joined: Fri Oct 10, 2014 8:12 am
Posts: 121
Location: earby lancs
Thanks for that will have to see if I can get better porla alined the power oak is brand new so it must be something I'm doing when setting up

_________________
Skywatcher 200p explorer EQ5 mount synscan upgrade kit
Nikon D3100


Top
 Profile Send private message  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group